Deck and Fence Staining in Portland and the Metro Area

Portland rain and moss wear out deck and fence finishes faster than most places. A good stain job starts with cleaning and drying the wood, then uses the right stain for how much grain you want to see. Ask any painter or stainer how they handle that prep before you book.

What deck & fence staining involves

Decks and fences take more weather than siding: horizontal surfaces hold water, and fences sit in wet soil and shade. Most metro decks need restaining every few years, and most fences need it every few years as well.

The biggest choice is stain type. Transparent and semi-transparent stains show the wood grain but need reapplying more often. Solid stains look like paint, hide weathering, and last longer, but you cannot easily go back to a natural look afterward.

Common projects

  • Deck restain (solid, semi-transparent, transparent)
  • Fence restain or full repaint
  • New deck or fence stain and seal
  • Pressure-treated wood weathering and seal
  • Cedar fence restoration
  • Composite deck cleaning

How a good deck & fence staining job is done

  1. 1

    Clean

    Wash off dirt, moss, and mildew with a deck cleaner, and use a stripper if old stain is peeling.

  2. 2

    Brighten and dry

    A wood brightener restores color on weathered cedar. The wood then needs to dry fully, often two or more dry days.

  3. 3

    Repair and sand

    Replace split or rotted boards, set nails and screws, and sand rough areas and railings.

  4. 4

    Stain

    Apply stain by brush, pad, or spray with back-brushing, following the manufacturer’s coverage and number of coats.

  5. 5

    Cure

    Keep furniture and foot traffic off until the stain has cured, usually 24 to 48 hours.

What deck & fence staining costs

What moves the price

Square footage and linear footage

Decks are usually priced per square foot. Fences are priced per linear foot or per panel, and both sides of a fence count separately.

Wood condition

Weathered, mossy, or splintered wood needs cleaning, sanding, and sometimes board replacement before staining.

Stripping old finish

Peeling solid stain or paint must be stripped before switching to a semi-transparent stain, which adds a full day or more.

Railings, spindles, and lattice

Detailed railings take far longer than open deck boards. Quotes should list them separately.

Every painting price range on the site is in the Portland painting cost guide, and the cost calculator turns them into a range for your house. The long-form walkthrough is how much it costs to paint a house in Portland.

Paint problems deck & fence staining fixes

Start from what you are seeing. Each card explains the usual cause before it points at a fix.

Deck staining

Decks wear out faster than any other stained surface because the boards are horizontal: rain sits on them, sun hits them directly, and people walk on them. A deck job starts with cleaning off dirt, moss, and mildew, and stripping any old stain that is peeling, followed by a brightener and enough dry days for the wood to dry all the way through.

Then come repairs and sanding: replacing split boards, setting raised nails and screws, and sanding rough spots and handrails. Railings, spindles, and stairs take much longer than open deck boards, so ask for them as a separate line in the quote. Expect to restain every 1 to 2 years with a transparent stain, every 2 to 4 with semi-transparent, and every 3 to 7 with solid stain.

Fence staining

Fences fail from the bottom up. The lower edges of boards and the posts sit in wet soil and shade, so that is where moss, mildew, and rot start, and where cleaning and repair time goes. Ask whether loose boards and leaning posts are in scope or need a fence contractor first.

Fence staining is usually priced per linear foot or per panel, and each side counts separately. Staining the neighbor’s side needs their permission and access. Many crews spray and then back-brush to work the stain into the grain, so plants, cars, and siding near the fence should be covered against overspray.

Cedar vs. pressure-treated wood

Cedar takes stain well and looks best with a semi-transparent finish, but its tannins can bleed through light solid stains without a blocking primer. Pressure-treated lumber is usually too wet to stain right after installation and should weather for a few months first. Composite decking does not need stain but benefits from periodic cleaning to control mildew.

How to compare quotes

Ask each stainer for a per-square-foot price for deck surfaces, a separate price for railings and stairs, and a per-linear-foot price for fences. Confirm the product, the number of coats, and whether cleaning and brightening are included. Those line items make it easy to see why one quote is higher than another.

Questions to ask before you hire

  • How will you clean and dry the wood before staining?
  • Which stain product are you using, and how many coats?
  • Are railings and stairs priced separately?
  • Will you replace damaged boards, or should I hire a carpenter?
  • How long must furniture and pets stay off?
  • How often will this product need reapplying?
Request a Free Estimate

Deck & Fence Staining FAQs

When is the best time to stain a deck in Portland?

Late spring through early fall, when the wood is dry and no rain is expected for 24 to 48 hours after application.

What is the best time of year to stain a fence in Portland?

The same dry window as decks and exteriors: late spring through early fall. The wood needs to be dry before you start, with no rain expected for 24 to 48 hours after the stain goes on.

How often do I need to restain my deck?

Transparent stains usually need a refresh every 1 to 2 years, semi-transparent every 2 to 4 years, and solid stains every 3 to 7 years, depending on sun and shade.

Should I use solid or semi-transparent stain?

Semi-transparent if you want to see the grain and do not mind more frequent maintenance. Solid if the wood is weathered or mismatched, or you want the longest-lasting finish.

Can I stain new pressure-treated wood right away?

Usually not. It needs to dry for a few months until water soaks in rather than beading on the surface.

How are fence staining quotes priced?

Usually per linear foot or per panel, and staining both sides costs more. Ask for the per-foot price so you can compare quotes.

Related guides

Related services and tools

Deck & Fence Staining by city

Other services

Ready for a Real Number?

Describe your project. Sending a request is free and carries no obligation. Before you hire anyone, check the license: Oregon CCB, or Washington L&I across the river.

Request a Free Estimate